Product Description

 

Product Description

Ball Bearings

Deep Groove Ball Bearings

Self Aligning Ball Bearings

Angular Contact Ball Bearings

Thrust Bearings

Applications
Electric motors
Elevators
Conveyor systems
Agriculture industry
Steering applications
Industrial pumps and drive cars
Pulp and paper industry
Industrial gearboxes
Trucks, trailers & buses

*Own Manufacturing Full Range*

GIL Bicycle Bearing 5202-ZZ Double-Row Angular Contact Ball Bearing

GIL Bicycle Bearing 5202-ZZ Double-row Angular Contact Ball Bearing. 
5202-ZZ double row shielded ball bearings possess higher radial and axial load capacities in either direction when compared to single-row ball bearings, they are found within a broad range of industrial and agricultural applications. The metal shields that are located on both sides of the bearing prevent unwanted debris from entering the bearing and also hold in the bearing grease. 

 

Product Parameters

*Remarks: 3200 / 3300 series same as 5200 / 5300 series

Bearing No.			dxDxB (mm)			Weight(kg)
3202	3202 ZZ	3202 2RS	15	35	15.9	0.064

 

More Choices

Please note our catalogue of this series,do not hesitate let us know what we can do for you.
*Remarks: 3200 / 3300 series same as 5200 / 5300 series

Bearing No.			dxDxB (mm)			Weight(kg)
3200	3200 ZZ	3200 2RS	10	30	14.3	0.049
3201	3201 ZZ	3201 2RS	12	32	15.9	0.057
3202	3202 ZZ	3202 2RS	15	35	15.9	0.064
3203	3203 ZZ	3203 2RS	17	40	17.5	0.095
3204	3204 ZZ	3204 2RS	20	47	17.5	0.150
3205	3205 ZZ	3205 2RS	25	52	20.6	0.175
3206	3206 ZZ	3206 2RS	30	62	23.8	0.286
3207	3207 ZZ	3207 2RS	35	72	27	0.436
3208	3208 ZZ	3208 2RS	40	80	30.2	0.590
3209	3209 ZZ	3209 2RS	45	85	30.2	0.640
3210	3210 ZZ	3210 2RS	50	90	30.2	0.690
3211	3211 ZZ	3211 2RS	55	100	33.3	0.986
3212	3212 ZZ	3212 2RS	60	110	36.5	1.270
3213	3213 ZZ	3213 2RS	65	120	38.1	1.560
3214	3214 ZZ	3214 2RS	70	125	39.7	1.800
3215			75	130	41.3	2.100
3216			80	140	44.4	2.650
3217			85	150	49.2	3.400
3218			90	160	52.4	4.150
3219			95	170	55.6	5.000
3220			100	180	60.3	6.100
3222			110	200	69.8	8.800

Company Profile

What We Do
Comprehensive product range:

– Bearings
– Oil seals, Transmission belt
– Chain and Sprocket
– Hub assembly & Wheel bearings
– Coupling, castings
– Linear motion

About Us
Focus on a variety of industries
Provide maintenance solutions
Optimize customer inventory and reduce cost

Vision
Continue to innovate through resource integration and business diversification to maintain uniqueness in the market

Mission
Provide comprehensive quality products and thoughtful customer service

Our Values
Behavior-based, service oriented, focused on results, and committed to continuous improvement
 

Advantage
1. Advanced Automatic Lines
2. Comprehensive Range
3. Premium Quality
4. Sustainability

Factory
Granville Industrial Co., Ltd.
HangZhou Granville Mechanical & Electrical Co., Ltd.
The advantage ball bearing factory located in the bearing manufacturing center – HangZhou, China. There are 2 plants, 1 specialized in manufacturing common grade ball bearings, another 1 professional in EMQ bearings with stablized Z3V3 quality. The factory takes her every effort in purchasing the most advanced bearing process equipments, NC automatic facilities are widely used in the factory and has becomes a bearing factory owning the most advanced process equipments in China. The Granville own ball bearing factory division manufacturing a whole range of radial deep groove ball bearings, open – shield – sealed – chrome steel, stainless steel available.

Product Offering:

Bore Size	3mm and up
Closures	Open, Non-contact metallic shields, Non-contact seals
Ring Material	52100 chrome steel 440C stainless steel 420C stainless steel
Seal Material	Nitrile, Polyacrylic, Viton
Retainer	Riveted steel, Crimped steel, Crowned steel, Crowned nylon
Precision Class	ABEC1, ABEC3, ABEC5, ABEC-7
Radial Clearance	C2, CO, C3, C4, C5
Heat stabilization	SO, S1, S2, S3

The Granville stablized high precision EMQ bearings in 10 series for below OE industries:
1 EM bearings for automobiles
2 EM bearings for air conditioners
3 EM bearings for industrial sewing machines
4 EM bearings for textile machines
5 Bearings for electric tools
6 EM bearings for general machinery
7 EM bearings for washers
8 EM bearings for vacuum cleaners
9 Bearings for bank note counters
10 EM bearings for cleanout machines

Workshop

Quality Warranty

Granville as a manufacturer of high quality products, guarantees compliance with the highest standards relative to the use of the best steel quality in the production process, the highest standards in the design of contact surfaces, as well as the most efficient packing and lubrication of parts. From material coming, quality control through all processes. Except interal test, goods to third party inspection if required. After the center of inspection and experiment being founded, effective methods of inspecting all kinds of raw materials are mastered and then the reliability of bearings is ensured. One of our main objectives is the continued improvement in the quality of our products and processes, in pursuit of which we obtained ISO certification 9001:2008 and TS16949. 

Advantage Manufacturing Processes and Quality Control:
01 Heat Treatment
02 Centerless Grinding Machine 11200 (most advanced)
03 Automatic Production Lines for Raceway
04 Automatic Production Lines for Raceway
05 Ultrasonic Cleaning of Rings
06 Automatic Assembly
07 Ultrasonic Cleaning of Bearings
08 Automatic Greasing, Seals Pressing
09 Measurement of Bearing Vibration (Acceleration)
10 Measurement of Bearing Vibration (Speed)
11 Laser Marking
12 Automatic Packing

The Different Types of Splines in a Splined Shaft

A splined shaft is a machine component with internal and external splines. The splines are formed in 4 different ways: Involute, Parallel, Serrated, and Ball. You can learn more about each type of spline in this article. When choosing a splined shaft, be sure to choose the right 1 for your application. Read on to learn about the different types of splines and how they affect the shaft’s performance.

Involute splines

Involute splines in a splined shaft are used to secure and extend mechanical assemblies. They are smooth, inwardly curving grooves that resist separation during operation. A shaft with involute splines is often longer than the shaft itself. This feature allows for more axial movement. This is beneficial for many applications, especially in a gearbox.
The involute spline is a shaped spline, similar to a parallel spline. It is angled and consists of teeth that create a spiral pattern that enables linear and rotatory motion. It is distinguished from other splines by the serrations on its flanks. It also has a flat top. It is a good option for couplers and other applications where angular movement is necessary.
Involute splines are also called involute teeth because of their shape. They are flat on the top and curved on the sides. These teeth can be either internal or external. As a result, involute splines provide greater surface contact, which helps reduce stress and fatigue. Regardless of the shape, involute splines are generally easy to machine and fit.
Involute splines are a type of splines that are used in splined shafts. These splines have different names, depending on their diameters. An example set of designations is for a 32-tooth male spline, a 2,500-tooth module, and a 30 degree pressure angle. An example of a female spline, a fillet root spline, is used to describe the diameter of the splined shaft.
The effective tooth thickness of splines is dependent on the number of keyways and the type of spline. Involute splines in splined shafts should be designed to engage 25 to 50 percent of the spline teeth during the coupling. Involute splines should be able to withstand the load without cracking.

Parallel splines

Parallel splines are formed on a splined shaft by putting 1 or more teeth into another. The male spline is positioned at the center of the female spline. The teeth of the male spline are also parallel to the shaft axis, but a common misalignment causes the splines to roll and tilt. This is common in many industrial applications, and there are a number of ways to improve the performance of splines.
Typically, parallel splines are used to reduce friction in a rotating part. The splines on a splined shaft are narrower on the end face than the interior, which makes them more prone to wear. This type of spline is used in a variety of industries, such as machinery, and it also allows for greater efficiency when transmitting torque.
Involute splines on a splined shaft are the most common. They have equally spaced teeth, and are therefore less likely to crack due to fatigue. They also tend to be easy to cut and fit. However, they are not the best type of spline. It is important to understand the difference between parallel and involute splines before deciding on which spline to use.
The difference between splined and involute splines is the size of the grooves. Involute splines are generally larger than parallel splines. These types of splines provide more torque to the gear teeth and reduce stress during operation. They are also more durable and have a longer life span. And because they are used on farm machinery, they are essential in this type of application.

Serrated splines

A Serrated Splined Shaft has several advantages. This type of shaft is highly adjustable. Its large number of teeth allows large torques, and its shorter tooth width allows for greater adjustment. These features make this type of shaft an ideal choice for applications where accuracy is critical. Listed below are some of the benefits of this type of shaft. These benefits are just a few of the advantages. Learn more about this type of shaft.
The process of hobbing is inexpensive and highly accurate. It is useful for external spline shafts, but is not suitable for internal splines. This type of process forms synchronized shapes on the shaft, reducing the manufacturing cycle and stabilizing the relative phase between spline and thread. It uses a grinding wheel to shape the shaft. CZPT Manufacturing has a large inventory of Serrated Splined Shafts.
The teeth of a Serrated Splined Shaft are designed to engage with the hub over the entire circumference of the shaft. The teeth of the shaft are spaced uniformly around the spline, creating a multiple-tooth point of contact over the entire length of the shaft. The results of these analyses are usually satisfactory. But there are some limitations. To begin with, the splines of the Serrated Splined Shaft should be chosen carefully. If the application requires large-scale analysis, it may be necessary to modify the design.
The splines of the Serrated Splined Shaft are also used for other purposes. They can be used to transmit torque to another device. They also act as an anti-rotational device and function as a linear guide. Both the design and the type of splines determine the function of the Splined Shaft. In the automobile industry, they are used in vehicles, aerospace, earth-moving machinery, and many other industries.

Ball splines

The invention relates to a ball-spinned shaft. The shaft comprises a plurality of balls that are arranged in a series and are operatively coupled to a load path section. The balls are capable of rolling endlessly along the path. This invention also relates to a ball bearing. Here, a ball bearing is 1 of the many types of gears. The following discussion describes the features of a ball bearing.
A ball-splined shaft assembly comprises a shaft with at least 1 ball-spline groove and a plurality of circumferential step grooves. The shaft is held in a first holding means that extends longitudinally and is rotatably held by a second holding means. Both the shaft and the first holding means are driven relative to 1 another by a first driving means. It is possible to manufacture a ball-splined shaft in a variety of ways.
A ball-splined shaft features a nut with recirculating balls. The ball-splined nut rides in these grooves to provide linear motion while preventing rotation. A splined shaft with a nut that has recirculating balls can also provide rotary motion. A ball splined shaft also has higher load capacities than a ball bushing. For these reasons, ball splines are an excellent choice for many applications.
In this invention, a pair of ball-spinned shafts are housed in a box under a carrier device 40. Each of the 2 shafts extends along a longitudinal line of arm 50. One end of each shaft is supported rotatably by a slide block 56. The slide block also has a support arm 58 that supports the center arm 50 in a cantilever fashion.

Sector no-go gage

A no-go gauge is a tool that checks the splined shaft for oversize. It is an effective way to determine the oversize condition of a splined shaft without removing the shaft. It measures external splines and serrations. The no-go gage is available in sizes ranging from 19mm to 130mm with a 25mm profile length.
The sector no-go gage has 2 groups of diametrally opposed teeth. The space between them is manufactured to a maximum space width and the tooth thickness must be within a predetermined tolerance. This gage would be out of tolerance if the splines were measured with a pin. The dimensions of this splined shaft can be found in the respective ANSI or DIN standards.
The go-no-go gage is useful for final inspection of thread pitch diameter. It is also useful for splined shafts and threaded nuts. The thread of a screw must match the contour of the go-no-go gage head to avoid a no-go condition. There is no substitute for a quality machine. It is an essential tool for any splined shaft and fastener manufacturer.
The NO-GO gage can detect changes in tooth thickness. It can be calibrated under ISO17025 standards and has many advantages over a non-go gage. It also gives a visual reference of the thickness of a splined shaft. When the teeth match, the shaft is considered ready for installation. It is a critical process. In some cases, it is impossible to determine the precise length of the shaft spline.
The 45-degree pressure angle is most commonly used for axles and torque-delivering members. This pressure angle is the most economical in terms of tool life, but the splines will not roll neatly like a 30 degree angle. The 45-degree spline is more likely to fall off larger than the other two. Oftentimes, it will also have a crowned look. The 37.5 degree pressure angle is a compromise between the other 2 pressure angles. It is often used when the splined shaft material is harder than usual.